.
سرفصل ها
Module 1 : PPP
• PPP Profile
- Local and remote addresses
- Incoming and outgoing filters
- Address list
- Change TCP-MSS
- Use encryption
- Session timeout
- Rate-limit configuration
- Only-one setting
• PPP Secret
- Service and Profile
- Local and Remote address
- Routes configuration
- Limit Bytes In/Limit Bytes Out configuration
• IP Pool
- Set addresses ranges
- Next pool options
Module 2 : PPTP, LT2P
• PPTP and L2TP
- Theory
- Comparison
• PPTP Client configuration
- Client setup
- Set profile
- Dial on demand
- Add default route and static routes
• PPTP Server configuration
- Enable server
- Setup profiles
- Add clients to PPP secret
- Set static interfaces for clients
• L2TP Client configuration
- Client setup
- Configure profile
- Dial on demand
- Add default route and static routes
• L2TP Server configuration
- Enable server
- Set profiles
- Add clients to PPP secret
- Set Static interfaces for clients
Module 3 : PPPoE
• PPPoE server and client
- Theory
- Usage environment
- Comparison to other PPP protocols
• PPPoE client configuration
- Client setup
- Select interface
- Service name
- Configure profile
• PPPoE Server configuration
- Enable PPPoE server
- Set profiles
- Add clients to PPP secret
- Add Static interfaces for clients
- Secure server by removing any IP address from PPPoE server interface
• Encryption
- Set profile without encryption
- Set profile with encryption
- Configure PPPoE client without encryption
• Interface ECMP
- Set ECMP routes for PPP interfaces
Module 4 : Bridging
• L2TP and EoIP
- Set L2TP tunnel
- Set EoIP tunnel
- Create bridge and add necessary interfaces to ports
- Confirm you have Ethernet connectivity between remote nodes
• L2TP and VPLS
- Set L2TP tunnel
- Set VPLS tunnel
- Create bridge and add necessary interfaces to ports
• L2TP and BCP
- Set L2TP tunnel
- Use BCP to bridge PPP interface
- Add to bridge necessary interface
• Multilink Protocol
- Enable multilink by specifying correct MRRU settings
- Disable mangle rules for MSS adjustment
• MLPPP (optional)
- Setup client and specify multiple interfaces for one client
- Set PPPoE server with MLPPP support
Module 5 : IPSec
• Introduction
- Theory and concepts
- Comparison to other VPN protocols
• IPSec Peer
- Use different authentication methods
- IPSec exchange modes
- Encryption and hash algorithms
- NAT-Traversal
- Lifetime and lifebytes
- DPD protocol
• Policy
- IPSec protocol and action
- Tunnels
- Generate dynamic Policy
• Proposal
- Encryption and authentication algorithms
- Lifetime
- PFS
• Installed-SA
- Flush SA
• Create IPSec between two routers with NAT
- Set peer
- Set policy
- Set NAT rules
- Confirm the secure link is established
Module 6 : HotSpot
• Introduction
- Concepts
- Usage environments
- Setup HotSpot with default settings
• HotSpot Login Methods
- HTTP CHAP/PAP
- MAC
- Cookie
- HTTPS
- Trial
- RADIUS
• Users
- Add users
- Set MAC-address for user
- Set MAC-address for username
- Limit Uptime and Limit Bytes In/Out
- Reset limits for user
• Monitor Users
- Host Table
- Active Table
- SNMP for users
• Monitor Users
- Host Table
- Active Table
- SNMP for users
• Profile
- Keepalive timeout
- Shared users
- Rate-Limit
- Address-list
- Incoming/Outgoing filter
- Incoming/Outgoing Packet Mark
• Bypass HotSpot
- Walled garden
- Walled garden IP
- IP binding
• Customize HotSpot
- Advertisement
- Customize pages
Module 7 : Radius
• RADIUS client
Add radius client
Set service
Use RADIUS for the specific service
• RADIUS server
• User manager
- Install the latest user-manager
- Add routers
- Add users
- Set profile
• RADIUS incoming
به عنوان اولین نفر، نظر خود را بنویسید!